DDPCA-300 Low-Noise Transimpedance Amplifier FEMTO
Contact Info
- Add:寶安區(qū)45區(qū)鴻都商務大廈C棟505室, Zip:
- Contact: 于沈洋
- Tel:13554997271
- Email:bnd015@szbonad.com
Other Products
The DDPCA-300 is a low-noise transimpedance amplifier. It features a minimum input noise of 0.2 fA/√Hz and a peak-to-peak noise of 0.4 fA. The gain can be adjusted manually or remotely, ranging from 10? to 1013 V/A. As a result, it covers a wide dynamic range of over 240 dB and can handle current values from sub-femtoamperes to milliamperes. Its compact housing allows installation close to the signal source, reducing noise caused by long cable runs. Built-in filters optimize amplifier bandwidth based on signal conditions, and the signal-to-noise ratio and measurement speed can be configured according to the application. Even at maximum gain, the measurement speed is sufficient for real-time femtoampere current measurements. At femtoampere levels, measurement errors and baseline drift may occur due to drift and offset currents, but the DDPCA-300 offers excellent long-term stability and minimizes drift.
| Model Name | DDPCA-300 | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Transimpedance [V/A] | 10? | 10? | 10? | 10? | 10? | 10? | 101? | 1011 | 1012 | 1013 |
| Bandwidth* (-3 dB) [Hz] | 400 | 400 | 400 | 400 | 150 | 150 | 20 | 20 | 1 | 1 |
| Rise Time (10-90%) [ms] | 0.8 | 0.8 | 0.8 | 0.8 | 2.3 | 2.3 | 17 | 17 | 350 | 350 |
| Integrated Input Noise (Peak-to-Peak) | 7 nA | 7 nA | 70 pA | 70 pA | 1.2 pA | 1.2 pA | 50 fA | 50 fA | 2 fA | 2 fA |
| Spectral Input Noise Density [A/√Hz] | 45 pA | 45 pA | 0.5 pA | 0.5 pA | 15 fA | 15 fA | 1.3 fA | 1.3 fA | 0.2 fA | 0.2 fA |
| Accuracy | Gain ±1% | |||||||||
| Variable Low-Pass Filter | 3 settings: Full bandwidth, 0.7 Hz, 0.1 Hz | |||||||||
| Output Performance | ±10 V, ±30 mA | |||||||||
| Bias Voltage | ±10 V, max 10 mA, adjustable via amplifier input connection, trimmer potentiometer, or remote control voltage | |||||||||
| Power Supply | ±15 V, +70 mA / -15 mA (typical), recommended ±150 mA | |||||||||
| Control Interface | 4 digital inputs (optically isolated), TTL/CMOS compatible, analog bias control voltage input | |||||||||
| Dimensions | 170 x 60 x 45 mm (L x W x H), 320 g | |||||||||
Bandwidth, rise time, and integrated input noise values are specified under full-bandwidth low-pass filter conditions. Lower peak-to-peak noise values can be achieved by setting the low-pass filter to 0.7 Hz or 0.1 Hz. Using a 0.1 Hz low-pass filter and a gain setting of 1012 or 1013 V/A enables a minimum peak-to-peak noise of 0.4 fA.
Offset can be adjusted via a trimmer potentiometer. Overload is indicated by an LED or digital control output. The input is protected against ±2 kV transients. Output is short-circuit protected. The power supply uses a 3-pin LEMO socket, and a compatible connector is included with purchase. An optional PS-15 power supply is also available.
| Industry Category | Electronic Components & Supplies/Integrated Circuits/Other Integrated Circuits |
|---|---|
| Product Category | |
| Brand: | FEMTO |
| Spec: | DDPCA-300 |
| Stock: | 1000 |
| Manufacturer: | |
| Origin: | China / Guangdong / Shenshi |
