Product Overview:

The PIA570 is a high-performance, low-noise current preamplifier designed for amplifying low-frequency weak current signals. It features configurable bandwidth and gain, making it suitable for a wide range of applications including cryogenic measurements, chip-level low-frequency noise measurement, sensor detection, photoelectric detection, audio engineering, and vibration engineering.

5 fA/√Hz input noise (typical)

1 MHz maximum bandwidth

Adjustable bias voltage and offset current

Two configurable bandwidth filters (low-pass/high-pass)

External power supply or battery operation

The instrument can be used standalone or integrated with devices such as oscilloscopes, lock-in amplifiers, and dynamic signal analyzers.

Input

The PIA570 converts current signals into corresponding voltage signals with a settable gain range from 1 pA/V to 1 mA/V. The input is fully floating (BNC shield* not connected to chassis ground). The preamplifier's feedback capacitance can be adjusted via Fb_c to fine-tune the bandwidth using a small screwdriver. Simultaneously, BIAS_V allows measurement of the currently set bias voltage value.

Output

Sensitivity

Sensitivity can be set from 1 mA/V to 1 pA/V. Two gain modes are available: low-noise mode, which allocates gain before the filter to optimize noise performance, and high-reserve mode, which allocates gain after the filter to reduce sensitivity to signal overload.

The BNC connector provides a 50? output impedance and can deliver a maximum signal of 10 Vpp to drive subsequent loads.

Filter

The PIA570 includes two programmable first-order RC filters. Different combinations allow for five filter mode settings:

LPF (6 dB/oct), BPF (6 dB/oct), HPF (6 dB/oct), LPF (12 dB/oct), HPF (12 dB/oct). Filter mode and cutoff frequency can be set via the front panel. The frequency range spans from 0.03 Hz to 1 MHz, increasing in a 1-3 sequence (e.g., 3 Hz, 10 Hz, 30 Hz, 100 Hz…).

Battery Operation

In addition to 220V AC mains operation, the instrument features built-in battery power. Battery mode significantly reduces power frequency interference, conducted disturbances, and wireless coupling interference, making it ideal for field applications. The rechargeable lithium battery provides up to 10 hours of operation. It charges automatically when connected to an external power supply, with a charging time of 4 hours. The front panel LED indicates the battery charging status.

PIA570 Low-Noise Preamplifier Specifications

Input

Bias voltage: -4V to +4V

Offset current: ±1 pA to ±5 mA

Input impedance: 1R (1 mA/V to 20 μA/V), 100R (10 μA/V to 200 nA/V), 10K (100 nA/V to 2 nA/V), 1M (1 nA/V to 1 pA/V)

Maximum input current: ±5 mA

Noise: Current noise 5 fA/√Hz at 1 kHz

Sensitivity: 1 mA/V to 1 pA/V

Gain stability: 100 ppm/°C (typical)

Bandwidth: DC to 1 MHz

Flatness: ±0.5 dB up to 300 kHz

Gain

Gain modes: Low-noise mode / High-reserve mode

Sensitivity: 1 mA/V to 1 pA/V

Filter

Filter modes: Five filter modes: LPF (6 dB/oct), BPF (6 dB/oct), HPF (6 dB/oct), LPF (12 dB/oct), HPF (12 dB/oct)

Cutoff frequency: 0.03 Hz to 1 MHz

Output

Maximum output: 10 Vpp into 50?

Filter reset: Filter time constant can be reset via front panel button

Other

Power consumption: 20W when charging, 6W when fully charged

Dimensions: 288 mm × 198 mm × 95 mm

Weight: 2960g (including battery)

Warranty: One year