Tsinghua Unisplendour eDCAP-601A Universal Protection and Control Device

1 Overview
The eDCAP-601A Universal Protection and Control Device is suitable for the protection and control of lines (incoming or outgoing lines) and certain outgoing equipment (such as outgoing transformers or grounding transformers) in systems with ungrounded, low-resistance grounded, or arc suppression coil grounded configurations at voltage levels below 110kV.
The eDCAP-601A Universal Protection and Control Device supports the IEC61850 station control layer communication protocol and enables the publishing and subscribing of substation events via the GOOSE network.

 Main Technical Specifications
1 Rated Parameters
Rated AC Voltage (Un): Line Voltage: 100V, 380V; Phase Voltage: 57.7V, 220V
Rated AC Current (In): 5A, 1A
Rated Power Frequency: 50Hz
Rated DC Power Supply: 220V, 110V

2 Environmental Conditions
Ambient Temperature:
Operating: Temperature range -10 to +55°C.
Storage: Temperature range -25 to +70°C. Under extreme conditions without applied excitation, the device shall not undergo irreversible changes and shall resume normal operation after temperature recovery.
Atmospheric Pressure: 80 to 110 kPa (relative altitude 2km and below)
Relative Humidity: The monthly average maximum relative humidity of the wettest month is 90%, with the monthly average minimum temperature of that month being 25°C and no condensation on the surface. At a maximum temperature of 40°C, the average maximum relative humidity shall not exceed 50%.
3 Power Consumption
AC Voltage Circuit: Not more than 0.5 VA per phase (at rated voltage)
AC Current Circuit: Not more than 0.75 VA per phase (at rated current)
DC Circuit: Not more than 10 W per protection unit (static) or 15 W (operating)
4 Thermal Stability
Continuous Operation: 2In, 1.5Un
Short-Time Overload: 20In, 1s
Instantaneous Overload: Peak 50In, 10ms
5 Measurement and Control Technical Specifications
(1) AC Power Frequency Input Quantities
a) Nominal Values
Voltage: 100V, 380V; Current: 1A, 5A; Frequency: 50 Hz.
b) Measurement Accuracy
Current, Voltage: 0.2In ~1.2In, 0.2Un~1.2Un: ±0.5%;
Active Power, Reactive Power, Power Factor: ±1%;
Frequency: ±0.02Hz.
c) Influence Quantities
Effect of Frequency Variation (45~55 Hz):
Permissible Variation: Current, Voltage ±0.5%; Power ±1%.
Effect of Temperature Variation (-10°C~+55°C):
Permissible Variation: Current, Voltage ±0.5%; Power ±1%.
Effect of Harmonic Content (20%) in Measured Quantity:
Permissible Variation: Current, Voltage ±0.5%; Power ±1%.
Effect of Overrange (120%) of Measured Quantity:
Permissible Variation: Current, Voltage ±0.5%; Power ±1%.
Effect of Self-Heating (30min):
Permissible Variation: Current, Voltage ±0.5%; Power ±1%.
Effect of Line Unbalance on Power Measurement:
Permissible Variation: ±1%.
Effect of Interaction Between Measured Circuits:

Permissible Variation: ±0.5%.
Effect of Power Factor Variation:
Permissible Variation: ±0.5%.
(2) Teleindication Quantities
a) Input circuits employ optoelectronic isolation;
b) Nominal Teleindication Voltage: DC Voltage 220V/110V. DC 24V input can also be provided as needed.
c) Teleindication Resolution ≤2ms
(3) Telemetry Response Time
Display Response Time ≤1s.
(4) Teleindication Response Time
Display Response Time ≤1s.
(5) Remote Control Output Contact Rating
DC 220V, 5A.
(6) Time Synchronization Function
Accurate to millisecond level.